Commercial Projects

Below are some of our Commercial Projects:

Ware House Reinforcement for H - Mart in Edmonton, Alberta (August 2020)

Gateway Mechanical Services hired HINGENEERING Consulting to provide structural assessment for an existing roof to hold the new insulation panels that will be used in the cooler and freezer area of H-Mart (The Largest Asian Super Markets in North America) in their Edmonton, Alberta location.

1/1

 Field Review Services for CX Grandin Tower in Downtown Edmonton, Alberta (January 2020)

​HINGENEERING Consulting had been awarded for the site review services of the a new commercial/residential high rise in downtown Edmonton, Alberta.  The photos below shows the snap shots of the foundations rebars before the concrete. 

1/1

Structural Reinforcement for Underground Parkade at 118 Avenue, Edmonton, Alberta (October 2019)

HINGENEERING Consulting scope of services was is the structural analysis and design of structural steel wide flanges, hollow steel sections were used for the parkade repairs and reinforcement. The photos below shows the existing conditions before doing the structural repairs. HINGENEERING Consulting provided the structural engineering services for the steel reinforcement of the existing parkade. 

1/1

Structural Assessment of Gas Station in Spedden, Alberta (September 2019)

HINGENEERING Consulting had been invited by CLAIMS Pro to assess the structural damages, caused to the retail shop of FAS GAS station located in Spedden, Alberta. The main scope of this structural appraisal report is to assess the structural integrity of the affected building components at the gas station and provide the required the structural recommendations for rehabilitation. 

1/1

Petro Canada Retail in Gibbons, Alberta (July 2019)

HINGENEERING Consulting carried out the structural  design and field reviews for Petro Canada Retail and the car wash located in Gibbons, Alberta. The structural design included the concrete foundations and timber wall load bearing design for the retail shop. For the car wash, the design included the cinder block wall and concrete foundations.

1/1

Engineering Services for Steel Arched Roof Framing in Millet, Alberta (April 2019)

HINGENEERING Consulting provided the structural engineering services for the steel framing supporting an arched roof panels roof system in Millet, Alberta. 

Structural Inspection Services for ATCO Multipurpose Building in Maskwacis, Alberta (December 2018)

HINGENEERING Consulting had been hired by MBG Buildings to provide the structural inspection for the structural steel building owned by Ermineskin Cree Nation in Maskwacis, Alberta. Our role is to make sure that the design drawings prepared by Behlen are implemented in the construction site.

1/1

Structural Inspection Services for HAT at Five Corners High Rise in Downtown Edmonton, Alberta (March 2018 to May 2019)

HINGENEERING Consulting had been hired by Glotman Simpson Consulting Engineers based in Vancouver to provide the structural inspection for the day to day activities for the Hat at Five Corners newly high rise building located at 10215 95 Street, NW in Edmonton, Alberta. Our role is to make sure that the design drawings prepared by Glotman Simpson are implemented in the construction site. The general contractor is the Calgary based giant contractor Cidex Construction. It has been a long journey from the top side photo when the construction started in March 2018 and the bottom side photo which was taken early October 2018 at level 5 pouring. 

1/1

Structural Inspection for Commercial Property in Downtown Edmonton, Alberta (October 2017)

HINGENEERING Consulting carried out the engineering inspection about the conditions of an existing commercial building. The existing commercial building was originally built in the 1950s. The purpose of this report was to provide an observation and structural assessment report on the physical condition and maintenance of the property and its improvements.

1/1

Engineering Services for Medical Clinic in Millwoods, Edmonton, Alberta (July 2016)

1/1

HINGENEERING Consulting had been invited to provide electrical and mechanical engineering services for a medical clinic. The engineering drawing package includes the electrical design, HVAC and plumbing layouts as well as supply and drainage details. The Coordination with the owners and the contractor was accomplished. The area of the clinic is approximately 2800 square feet.

Construction Engineering for Connecting Elevator Hoist to Roger Place, Edmonton, Alberta (May 2015)

The project entails the structural analysis and design of safe connections of the elevator hoist to the main steel structure of the Edmonton Arena to facilitate the construction. This includes

  1. Analysis and design of various Tie-in horizontal and diagonal braces from the elevator mast to the main structure.

  2. Design of the anchoring system between the Tie-in braces to the the main structure to withstand the acting wind loads.

  3. Provide structural recommendation to connect the Elevator hoist to the roof of the Arena.

  4. Act as the structural consultant for the elevator hoist supplier to the Arena main contractor (PCL).

1/1

Edge Water Condo Tower at Jasper Avenue in Edmonton, Alberta (March 2015)

The project entails the structural analysis and design of elevator beam connections against the elevator rail roads for six levels.
The structural review was carried out to assess the proposed solution by Pagnotta Industries for the bolted and welded connections for the lower level floors, where the plates were installed above the concrete shaft surface. 

1/1

Structural Engineering Assessment of Commercial property in Edmonton, Alberta (May 2015)

The project entails the structural analysis and design of the existing timber framing, which constitutes the North West half of the third floor level of the existing commercial property. Hingeneering Consulting recommended the wall framing strengthening. 

1/1

Ford Northstar Building - Fort McMurray, Alberta (July 2014)

Reviewed the structural configuration of the aluminum framing on the second floor of the building. The purpose of this calculation was to verify the adequacy of the aluminum cross-sections used in the horizontal and vertical mullions to resist the gravity and wind loading in addition to satisfying the deflection requirements. The review was extended to include the strengths of the screw fasteners connecting the vertical mullions to the structure. 

1/1

ICE Building - University of Alberta, Edmonton, Alberta (June 2014)

Structural design for custom-designed steel clamps and rigging equipment for lifting of precast panels. In addition, we were responsible for the following:

  • Structural analysis and design for steel clamps to carry the precast concrete panel

  • Identify the number of designed steel clamps, beam clamps, master links, chain slings, etc. 

  • Check the rigging tools available to attach it to the design clamp

1/1

Skylight for PCL Building - Edmonton, Alberta (April 2014)

The main scope is to verify the adequacy of the aluminum cross-sections used in the head purlin and the transverse rafters. Moreover, the review is extended to cover the strengths of the fasteners connecting the sky light with the concrete wall (apex) and the concrete curb (base).

1/1

© 2021 Hingeneering Consulting. 

Alberta. 1-587-315-7222

British Columbia. 1-604-256-9490

Email.  info@hingeneering.com